Moin,
hab mein etrex20 lange nicht benutzt und versuche es jetzt wieder mit meinem Linux-Rechner zu verbinden. Dabei wird das Gerät an sich erkannt, aber nicht die Partitionen darauf:
Auszug aus dmesg:
Sagt das jemandem was?
Das changelog von Firmware 4.50 liest sich interessant:
Das Verhalten ist an 2 verschiedenen PCs identisch, es liegt also am etrex.
hab mein etrex20 lange nicht benutzt und versuche es jetzt wieder mit meinem Linux-Rechner zu verbinden. Dabei wird das Gerät an sich erkannt, aber nicht die Partitionen darauf:
Code:
$ ls /dev/sd{d,e}*
/dev/sdd /dev/sde
Code:
$ cat /proc/partitions
major minor #blocks name
[...]
8 48 1953792 sdd
8 64 31166976 sde
Auszug aus dmesg:
Code:
[2518288.806337] usb 3-11: new full-speed USB device number 9 using xhci_hcd
[2518288.806575] usb 3-11: Device not responding to set address.
[2518289.010414] usb 3-11: Device not responding to set address.
[2518289.214409] usb 3-11: device not accepting address 9, error -71
[2518306.554292] usb 3-11: new full-speed USB device number 11 using xhci_hcd
[2518306.571277] usb 3-11: New USB device found, idVendor=091e, idProduct=2519
[2518306.571279] usb 3-11: New USB device strings: Mfr=0, Product=0, SerialNumber=5
[2518306.571281] usb 3-11: SerialNumber: 0000e559d2a8
[2518306.572535] usb-storage 3-11:1.0: USB Mass Storage device detected
[2518306.572685] scsi7 : usb-storage 3-11:1.0
[2518307.571936] scsi 7:0:0:0: Direct-Access Garmin GARMIN Flash 1.00 PQ: 0 ANSI: 5
[2518307.572862] scsi 7:0:0:1: Direct-Access Garmin GARMIN Card 1.00 PQ: 0 ANSI: 5
[2518307.573077] sd 7:0:0:0: Attached scsi generic sg3 type 0
[2518307.573186] sd 7:0:0:1: Attached scsi generic sg4 type 0
[2518307.579806] sd 7:0:0:0: [sdd] 3907584 512-byte logical blocks: (2.00 GB/1.86 GiB)
[2518307.580805] sd 7:0:0:1: [sde] 62333952 512-byte logical blocks: (31.9 GB/29.7 GiB)
[2518307.582371] sd 7:0:0:0: [sdd] Write Protect is off
[2518307.582373] sd 7:0:0:0: [sdd] Mode Sense: 23 00 00 00
[2518307.583365] sd 7:0:0:1: [sde] Write Protect is off
[2518307.583366] sd 7:0:0:1: [sde] Mode Sense: 23 00 00 00
[2518307.584328] sd 7:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[2518307.585336] sd 7:0:0:1: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[2518307.605656] sdd:
[2518307.617855] sde:
[2518307.635196] sd 7:0:0:0: [sdd] Attached SCSI removable disk
[2518307.636241] sd 7:0:0:1: [sde] Attached SCSI removable disk
Sagt das jemandem was?
Das changelog von Firmware 4.50 liest sich interessant:
Aber wenn ich keine Dateien auf das Gerät kopieren kann, kann ich auch nicht updaten (aktuell ist 4.30 drauf)Improved detection of USB connection to a PC.
Das Verhalten ist an 2 verschiedenen PCs identisch, es liegt also am etrex.